Be sure to leave a little space between your skin and the bracelet, so that you can roll it over your wrist without breaking the stretch cord. The ends can be slippery and the last thing you want is to drop the cord and see all those fabulous beads slide off the end!Stretch bracelets are fast and easy to make. Be sure to leave a little space between your skin and the bracelet, so that you can roll it over your wrist without breaking the stretch cord. If you make another bracelet using smaller or larger beads, you should check for fit again with those, because you may need the bracelet to be slightly shorter or longer.Knotting your stretch bracelet takes the most practice.
Some people say it makes the cord brittle and more prone to breakage. Make sure that the last bead you string has a hole large enough to hide a knot … You may prefer to use something more slow-drying like E6000 and then simply allow them to dry before wearing your bracelet.When you are working with small beads like these that are all the same size, mixing in a few beads with a larger hole will make it easier for you to hide the knot.Do your best to hold the first half of the knot in place, and then tie the second part of the knot and pull firmly to secure.
Lisa Yang. This makes your elastic bracelet look nicer, but also protects the knot from wear caused by rubbing between two beads. This will prevent your stretch bracelet from sagging.Once the glue has dried, very gently, stretch out each cord end, and then use embroidery scissors to trim the end close to the beads.With the glue still tacky, hold the cord between two beads about an inch away from the knot, and tug gently to pull the knot inside of the adjacent bead. My eight-year-old niece has a bracelet I’ve made this way (four knots total, all glued and “buried”) and it’s held up for several years without problems. Don't Stretch Your Bracelet to Put It On . In the meantime, you can make a few more bracelets to wear stacked, and even string up some shorter matching finger rings.Not everyone agrees with using glue on the knot of elastic bracelets.
.
Seed beads work well because their small size makes them lightweight and most have very smooth holes. Thinner elastic cord can stretch out more quickly with heavier beads unless you use a double strand.Start by making your stretch bead bracelets with good quality elastic cord meant for jewelry making. They are also easy to make, and they can last for a long time if you follow these tips.Cut a piece of cord the size of your bracelet, plus leave yourself at least three inches of elastic on each side to tie your knots. Check the length occasionally by wrapping the strung beads around your wrist. A clear cord is an obvious choice, but it can actually be more noticeable with dark colored beads. A correctly tied knot will last better in the long run.Fashion trends come and go, but elastic bracelets remain popular because they are versatile and easy to wear. Follow these tips to make them last:Choose a color elastic that is complementary to the beads you are using. That is not our experience.Chris Franchetti Michaels / The SpruceString all of the beads for your bracelet. Many kinds of wood and shell beads also work nicely.For this bracelet, we're using 0.5mm black stretch floss cord.Additional tools and materials to have on hand:When choosing a glue you may want to consider that super glue is by far the fastest-drying option, but it makes it more difficult to hide your knot and makes it easy to accidentally glue your fingers together. 04 of 04.
Carefully make the first half of a square knot, gently pulling the cord ends to remove slack in the bracelet.When you choose beads, select ones that are lightweight and don't have sharp edges around the holes. How you care for your elastic bracelet is just as important as how you make it. Another plus is that they can be as casual or elegant as you'd like.Just make sure the beads have smooth holes to avoid cutting or wearing away the elastic cord.Once the glue has dried, your new stretch bracelet will be ready to wear. Free tutorial with pictures on how to tie a knot in under 5 minutes by knotting with elastic, cement, and clear nail polish. It can be tricky at first to complete a knot without losing tension in the bracelet and allowing spaces to form between the beads. This will make it less likely that the knot will loosen when you are trimming them.Some people use crimp beads, rather than knots, to secure the ends of the stretch cord. The cord is slippery and nothing is worse than having everything exactly like you want it, and then dropping the end during tying.The most popular sizes of elastic cord for making bracelets is 0.7 mm or 1 mm elastic cord, but selecting one depends on the weight of the beads and the size of the hole. After completing a few bracelets, this should become much easier.While holding the bead away from your knot, apply a tiny drop of glue to the knot.Let the glue dry before trimming the cord ends. This also helps to ensure that no areas of the empty card show through.